Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Kennedale, TX
Gate access control in Kennedale means keypads, remotes, card readers, and intercoms wired to gates sitting on acreage parcels, where the Blackland Prairie clay shifts posts seasonally and long driveways make the gate the only way in or out. Most homes here run ornamental iron or tubular steel swing and slide gates from the 1980s and 1990s, so the electronics often need modern interface work while the steel stays put. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule equipment. Call (682) 564-0512 any hour and a live person answers.
Why Kennedale Homes Are Different
Kennedale sits inside the DFW Metroplex but behaves like a semi-rural enclave, with a far higher share of acreage lots and private driveway gates than Arlington or Mansfield. That density of gate infrastructure per household is the whole story. These gates ride on posts set into Tarrant County’s Blackland Prairie expansive clay, which swells in wet months and contracts hard during summer drought. The result is a seasonal heave-and-settle cycle that throws posts out of plumb, drops gates, and tears hinge welds, repeating every few years even on well-installed work.
The housing stock runs heavily to 1970s and 1980s ranch homes plus newer custom builds on half-acre to multi-acre parcels. Many of those older properties still carry the original tubular steel swing gates. Their hinge welds have corroded through decades of ground movement and surface rust, but owners often keep them because the weathered steel matches the ranch character of the property. We weld and fabricate around that preference rather than pushing replacement. Triple-digit summer heat also takes a toll on opener internals: worm gears, limit switches, and battery backups on solar-powered systems fail more often here than in shaded suburbs.
Our Main Kennedale Services
Kennedale homeowners call most about keeping existing gates running and replacing them when the steel or the electronics are done. Here are the three services with their own detailed Kennedale pages.
Gate Repair in Kennedale
Repair work in Kennedale usually starts with post movement from the clay soil, which pulls hinges out of alignment and leaves the gate dragging at the latch side. We reset, shim, or replace posts, rebuild hinge brackets, and adjust travel so the gate closes clean. For automatic gates, the same soil shifts throw limit switches off and strain the opener. We diagnose the motor and controls, then make the repair in one visit when parts are on the truck. Full details are on the Gate Repair in Kennedale page.
Gate Installation in Kennedale
New gates in Kennedale have to be engineered for moving ground. We size posts for the Blackland Prairie soil and set them deeper than a standard slab install, because a post that starts plumb will not stay plumb through a wet winter and a dry summer on expansive clay. That planning applies to ornamental iron, tubular steel, and custom ranch-style gates. We also account for long driveway runs and solar or hardwired power access. See the Gate Installation in Kennedale page for the full scope.
Gate Motor & Opener in Kennedale
Motors and openers in Kennedale live harder lives than in most metro areas because of the heat and the dust from unpaved acreage driveways. Limit switches drift, worm gears wear, and solar battery backups fail in a few seasons. We repair the existing opener when it is economically repairable and replace it with the correct brand and duty rating when it is not, across all nine brands we stock parts for. The Gate Motor & Opener in Kennedale page covers diagnostics, brands, and pricing.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterGate Access Control in Kennedale
Gate access control in Kennedale is the electronics that decide who gets in: keypads, remotes, phone entry, card readers, and video intercoms. On acreage properties with gates set back from the road, the system also has to survive long wire runs, solar power, and the same clay that moves the gate itself. The job is different here because most access systems are retrofitted onto 1980s and 1990s gates whose posts have already moved, so the electronics have to be mounted and wired with that movement in mind. We service and install systems from Viking, Ghost Controls, DoorKing, and Elite, and every visit leaves a written price before work begins and a documented photo record when we leave. This is what our Gate Access Control work looks like in Kennedale.
Keypad Entry
Signs you need it
The keypad is cracked, buttons stop responding, or the code works intermittently after rain.
What it costs in Kennedale
Keypad replacement or wired keypad installation in Kennedale typically runs $110-$390.
How we do it
We mount the new keypad in a position that clears the gate’s travel arc, run sealed low-voltage wire away from post movement joints, program the codes, and photograph the final setting.
Remote Control
Signs you need it
Remotes work only from a few feet away, or the gate stops responding to one or all remotes after a power event.
What it costs in Kennedale
Remote programming or replacement transmitters in Kennedale typically run $70-$160.
How we do it
We read the existing receiver brand and frequency, pair new transmitters to the opener, and hand you a written note of every remote coded to the system so nothing is left unaccounted.
What Gate Access Control Costs in Kennedale
| Item | Typical range in Kennedale |
|---|---|
| Keypad repair or replacement | $110-$390 |
| Remote programming or replacement | $70-$160 |
| Full access control upgrade | $750-$2,800 |
Can you add a keypad to an automatic gate in Kennedale?
Yes, most automatic gates in Kennedale can take a wired or wireless keypad, even older 1980s steel swing gates, as long as the opener has a compatible receiver or a hardwired input. The main complication is running low-voltage wire across ground that moves seasonally. We mount the keypad on a stable post and leave slack where the soil shifts. Call (682) 564-0512 for a written quote.
Do solar-powered gate openers hold up in Kennedale heat?
They do, but the battery is the weak point. Triple-digit summers shorten the lifespan of solar backup batteries, especially on south-facing panel mounts with no shade. We see battery replacement every two to three years on many Kennedale acreage systems. A good battery and a clean panel keep the system reliable through summer. Call (682) 564-0512 for an on-site check.
Gate Parts & Welding in Kennedale
Gate parts and welding in Kennedale is the structural side of the trade: hinges, posts, rails, rollers, and the custom fabrication that keeps older ranch-style gates in service. The Blackland Prairie clay that moves posts also rips hinge welds and lets rails sag until the gate won’t latch. Many of the gates we weld on are original 1980s tubular steel, where the hinge has corroded through and the owner wants the weathered look preserved, not replaced. We cut out the failed section, form and weld a new hinge in place, and document every measurement so the next repair starts from a record instead of a guess. Weld repair is part of our Gate Parts & Welding work.
Hinge Replacement
Signs you need it
The gate sags on the latch side, scrapes the ground, or the hinge pin has visible play and rust scale.
What it costs in Kennedale
Hinge replacement or weld repair in Kennedale typically runs $180-$520 per hinge.
How we do it
We take the gate’s weight off the hinge, cut out the failed weld or bearing, form the replacement, weld it square to the post and frame, and photograph the final position before and after paint.
Post Replacement
Signs you need it
The post leans visibly, the gate gap opens or closes with the seasons, or the post base has cracked the surrounding concrete cap.
What it costs in Kennedale
Post removal and replacement in Kennedale typically runs $300-$1,000 depending on depth and concrete.
How we do it
We dig out the old post, set the new one below the local frost and clay movement line with a proper concrete collar, brace it square, and reset the gate so it travels clean.
What Gate Parts & Welding Costs in Kennedale
| Item | Typical range in Kennedale |
|---|---|
| Hinge replacement or weld repair | $180-$520 per hinge |
| Gate roller replacement | $120-$320 per roller set |
| Post removal and replacement | $300-$1,000+ |
Can you weld the original gate instead of replacing it?
Yes, and in Kennedale that is often the right call. The original 1980s tubular steel gates match the ranch character of the property, and weld repair restores the hinge or rail instead of tearing out the whole gate. Call (682) 564-0512 and we’ll give you a written price before any cutting starts.
How long does a welded hinge repair last here?
A properly formed and painted hinge weld on a Kennedale gate typically lasts years, but the post it is attached to is the real variable. If the post is moving in the Blackland Prairie clay, even a perfect weld will stress. We check post stability as part of every hinge repair and tell you if the base needs work first. Call (682) 564-0512 for a free estimate.
Brands We Service in Kennedale
We stock parts for Viking, Ghost Controls, DoorKing, and Elite openers on our trucks, along with LiftMaster, FAAC, BFT, Linear, and Mighty Mule components. That means most access control and opener repairs in Kennedale happen in one visit. See our brands for the full lineup.
Pricing for Gate Repair in Kennedale, TX
| Service | Typical range in Kennedale |
|---|---|
| Keypad repair or replacement | $110-$390 |
| Remote programming or replacement | $70-$160 |
| Full access control upgrade | $750-$2,800 |
| Hinge replacement or weld repair | $180-$520 per hinge |
| Gate roller replacement | $120-$320 per roller set |
| Post removal and replacement | $300-$1,000+ |
In Kennedale, the price moves up when the post has failed at the base, when the gate is on solar power with a dead battery, or when the wiring was never run in conduit and has corroded underground. Our written price covers everything we plan to do, and you approve it before any work begins, exactly as the Haven Standard requires.
Neighborhoods We Serve in Kennedale
We work the whole city, including the acreage lots along Kennedale Sublett Road, the older ranch parcels around Mansfield Cardinal, and the newer custom-home streets off New Hope Road. Most Kennedale jobs get a same-day or next-day visit.
- Kennedale Sublett Road corridor
- New Hope Road area
- Mansfield Cardinal acreage parcels
- Wild Wild West area
- Blair Road ranch homes
Service Area - Cities Near Kennedale
From Kennedale, we also serve Arlington, TX, Mansfield, TX, Burleson, TX, and Fort Worth, TX. Dispatch is coordinated from our Dallas-Fort Worth office, and crews travel to Kennedale daily.
Serving Kennedale, TX - Our Local Coverage Area
We’re based in the Kennedale area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Kennedale
Most repair calls in Kennedale get a next-day visit, and many get same-day service when we already have a crew in the area. Emergency calls for a gate stuck open or closed are handled right away. Call (682) 564-0512 and a live person answers at any hour.
Most hinge, weld, opener, and access control repairs don’t require a permit in Kennedale. New gate installations and major post work can trigger permit requirements depending on the project scope and the specific property. We check the current city requirements before starting anything structural and tell you what’s needed.
Yes, that is most of Kennedale. Long driveway runs mean wider gates, solar or hardwired power decisions, and openers sized for heavier use. We look at the gate’s duty cycle and the power situation before recommending a repair or replacement, and the written price covers the whole job.
Need a gate fixed or an access system updated in Kennedale? Call Vance Gate Repair at (682) 564-0512 for a free estimate and a written price before any work starts.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Kennedale Customers Say
"The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C.