Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Irving, TX
Gate access control in Irving usually means one of two things: a keypad or phone-entry system that stopped talking to an HOA-managed entry gate, or a slide-gate operator on a Valley Ranch or Las Colinas property that no longer responds to the command signal. Most of the access-control work we do here is tied to the master-planned communities built through the 1980s and 90s, where whole subdivisions share gate hardware that was installed in bulk and is now failing at roughly the same time. The same black clay soil that heaves those gate posts also pulls underground loop-detector wires loose, so what looks like a keypad problem is often a broken wire six inches below the driveway. Call (682) 564-0512 and we’ll put it in writing before anyone picks up a tool.
Why Irving Homes Are Different
Irving’s residential gate stock splits into two distinct generations. The Valley Ranch and Las Colinas planned communities carry ornamental iron swing and slide gates with in-ground loop detectors that were original developer features, and many of those operators are now 25 to 35 years old. The older pockets closer to downtown Irving have 1950s and 60s bungalows with simpler driveway gates and wood privacy-fence gates. What both share is the Blackland Prairie shrink-swell clay underneath them. Wet winters heave gate posts out of plumb; summer droughts pull soil away from footings. The cycle throws automated operators out of alignment and cracks welds at hinge brackets, which is why Irving gate work so often starts with the post, not the motor. North Texas ice storms add another layer: freezing rain loads ornamental iron gates and seizes operator gearboxes that then burn out when the motor forces movement.
Our Main Irving Services
Most Irving homeowners reach us through one of three doors: a gate that stopped opening, a gate that needs to exist where none does, or a motor that quit. Here is where each leads.
Gate Repair in Irving
A swing gate that drags on the driveway, a slide gate that shudders halfway, a weld cracked at the hinge bracket: these are the calls we make in Valley Ranch and Las Colinas every week. Irving’s clay soil shifts posts seasonally, so we check alignment before we touch the operator. Full details on Gate Repair in Irving.
Gate Installation in Irving
New gates in Irving usually mean working around existing HOA design rules, particularly in the master-planned sections where entry gates must match the original ironwork. We measure, price the full job in writing, and schedule the work. See Gate Installation in Irving.
Gate Motor & Opener in Irving
When the gate itself is fine but the operator won’t run, we diagnose the motor, the limit switches, and the control board before quoting a replacement. In Irving’s older planned communities we see a lot of original operators that simply reached end of life within a few years of each other. Details at Gate Motor & Opener in Irving.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterGate Access Control in Irving
Gate access control in Irving is shaped by the city’s planned-community layout. Valley Ranch and Las Colinas subdivisions were built with gated entries from day one, which means HOA boards manage access systems covering dozens of units rather than one driveway. Thirty-year-old slide-gate operators on those systems are now failing in waves, and the command hardware, keypads, phone-entry modules, card readers, wears out on the same timeline. We work across the systems already installed, with service history on LiftMaster, FAAC, and BFT controllers, and every visit ends with a written record of what was adjusted or replaced. You can also read more on our Gate Access Control hub page.
Keypad Entry
Signs you need it
Residents report the keypad accepts the code but the gate doesn’t move, or the keypad beeps but never activates the operator.
What it costs in Irving
Keypad replacement or reprogramming in Irving typically runs $180 to $520, depending on whether the controller, wiring, or only the keypad itself is at fault.
How we do it
We test the keypad output at the control board, confirm power and ground, then replace or reprogram and photograph the new settings.
Phone Entry
Signs you need it
Calls from the entry pedestal ring once and drop, or residents can’t open the gate from their phones anymore.
What it costs in Irving
Phone-entry repair in Irving typically falls between $220 and $640, with cellular-module replacement at the upper end.
How we do it
We trace the phone line or cellular signal, confirm the relay output, and replace the module or reconfigure the directory, then test with a live call.
What Gate Access Control Costs in Irving
| Item | Typical range in Irving |
|---|---|
| Keypad replacement | $180 - $520 |
| Phone-entry module | $220 - $640 |
| Card reader or vehicle detector | $260 - $580 |
Can you fix an HOA gate system without replacing all the hardware?
Usually yes. The keypad, phone module, or loop detector is a separate component from the operator. We replace the failed part, not the whole system, and leave a written record of exactly what changed.
How fast can you get to a Valley Ranch entry gate?
Most Irving access-control calls are dispatched the same day. A live person answers 24/7, so an HOA board member or resident reports the problem once and we schedule from there.
Gate Parts & Welding in Irving
Gate parts and welding in Irving follow the soil. The Blackland Prairie clay under this city expands in wet winters and contracts through summer droughts, and that movement cracks welds at hinge brackets, pulls posts out of plumb, and distorts rails on slide gates. In Valley Ranch and Las Colinas, 30-year-old ornamental iron gates are reaching the age where hinges fatigue and rollers wear flat. We stock the common replacement parts and weld on site. More detail lives on our Gate Parts & Welding hub page.
Hinge Replacement
Signs you need it
The gate sags on the latch side, scrapes the ground at the swing end, or the hinge pin shows visible wear.
What it costs in Irving
Hinge replacement in Irving typically runs $95 to $260 per hinge, depending on gate weight and whether the post needs shimming.
How we do it
We lift the gate, cut or unbolt the old hinge, weld or bolt the new one, and reset the gate so it clears the ground evenly.
Post Replacement
Signs you need it
The gate post leans visibly, the gate drags on one side, or cracks radiate from the base of the concrete footing.
What it costs in Irving
Post replacement in Irving typically falls between $600 and $1,500, with concrete work and soil conditions driving the range.
How we do it
We brace the gate, remove the old post and footing, set a new post in concrete sized for the clay soil, and rehang the gate after the pour cures.
What Gate Parts & Welding Costs in Irving
| Item | Typical range in Irving |
|---|---|
| Hinge replacement | $95 - $260 per hinge |
| Post replacement | $600 - $1,500 |
| Rail repair or custom weld | $180 - $490 |
Can you weld ornamental iron to match the original gate?
Yes. We match the existing profile and paint finish where possible, and photograph the repair before and after. On HOA gates, we can produce the photo record the board usually wants.
Do you stock parts for older Irving gates?
We keep common hinges, rollers, brackets, and operator parts on the truck. For odd or obsolete hardware we order same-week and schedule the weld work around the part arrival.
Brands We Service in Irving
We service LiftMaster, Mighty Mule, and FAAC operators most often in Irving, with parts stocked for each. See the full our brands list for every manufacturer we work on and the documentation we leave behind.
Pricing for Gate Repair in Irving, TX
| Service | Typical range in Irving |
|---|---|
| Keypad entry repair | $180 - $520 |
| Phone-entry module | $220 - $640 |
| Card reader or vehicle detector | $260 - $580 |
| Hinge replacement | $95 - $260 per hinge |
| Post replacement | $600 - $1,500 |
| Rail repair or custom weld | $180 - $490 |
What pushes an Irving gate repair toward the top of these ranges is usually the post: if the clay has moved a gate out of plumb, we correct the alignment before the new part goes on. Every price is written down and handed over before work begins, and it does not change when the invoice arrives.
Neighborhoods We Serve in Irving
We work across Irving, with the densest concentration of gate work in the planned communities where gates were built as original equipment. We typically reach most Irving addresses the same day for repair calls.
- Valley Ranch
- Las Colinas
- Heritage District
- Cottonwood Valley
- University Hills
Service Area - Cities Near Irving
We also serve the surrounding area: Grand Prairie, TX, Cedar Hill, TX, Euless, TX, and Bedford, TX. The same written-price rule applies on every job, wherever the gate is.
Serving Irving, TX - Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Irving
A live person answers the phone 24/7 and most Irving repair calls are scheduled the same day. Emergency and scheduled work both start with a written price before the work begins, so you’ll know where you stand before we dispatch.
Many Valley Ranch and Las Colinas communities require HOA approval before gate hardware changes, especially at entry gates. We provide written scope and photo documentation in advance, which most boards ask for anyway.
Yes. Installation and access-control upgrades are scheduled work: we measure, write the price, and set a date that gives you time for whatever board approval your community needs.
Call (682) 564-0512 for a free estimate on any gate repair in Irving, TX. We’ll put the price in writing before any work starts, and leave you a photo record of what we did when we’re done.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Irving Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.